Door Hanger Rollers and Upthrusts

All outside diameters noted are rolling diameters. Inform your representative if you’ve measured rim to rim or rolling diameter.

 

456EP2

Roller, Steel, 2.31″ OD, 0.56″ W, 1/2″-12 threads, assembly of round profile roller, bearing, bolt & washer. For type “B” hoistway door hangers, formerly p/n 456G1

 

 

456CC1

Roller, steel, 2.5″ OD, 0.76″ W, 0.78″ ID, roller & (2) washers, used on integral & 7060 hoistway door hangers

 

 

456CC2

Roller, poly tire, 2.5″ OD, 0.76″ W, 0.78″ ID, roller & (2) washers, used on integral & 7060 hoistway door hangers

 

 

456W1

Door Roller, poly tire, 3″ OD, .75″ W, .98″ ID, used for “A” hoistway hangers & AU car door hangers

 

 

A456W1

Door Roller, poly tire, 3″ OD, .75″ W, .5″ ID, used for “A” hoistway hangers & AU car door hangers

 

 

A456EA1

Door Roller, 3″ OD, .75″ W, .5″ ID, used for “A” & “AU” hangers (note round track profile upwards)

 

 

A456EA2

Door Roller, 3″ OD, .75″ W, .5″ ID, used for “A” & “AU” hangers (note round track profile upwards)

 

 

 

A456FC1

ROLLER, HANGER – SCREW OPERATOR (FOR TUBULAR TRACK)

 

456CX4 (No longer available)

For service replacement, discard old roller and pin and use either 456EW1 or EW2. 456EW2 only needed for 2 speed door type clearance applications.

 

 

 

456EW1

Door roller, 3″ OD, .8″ W, .67″ ID – with permanent eccentric 1/2″ pin.

 

 

 

456EW2

Door roller, 3″ OD, .8″ W, .67″ ID – with reversible eccentric 1/2″ pin. replaces 456CX4 in 2-speed applications

 

 

2700CAF2

Roller Kit, 3″ OD, .8″ W, .78″ ID, consisting of upper roller & retaining ring – early OVL hangers

 

 

AAA456YA3

Hanger Roller Kit, M12 stud with hardware – 1999-2006 applications & 2002 – present  –  Mod track & hanger applications (identical to 456EW1 but metric)

 

 

AAA456YA4

Hanger Roller Kit, M12 permanent eccentric pin with hardware (later OVL door applications) – replaces AAA456XD1

 

 

AAA456ZB1

Hanger Roller – non-eccentric, round profile – M8 internal threaded locking hub – Otis NG door systems

 

 

 

 

 

456DH3

Vendor entrance (NH INDUS.) applications. Unique eccentric slotted hub. 1/2″ Stud.

 

 

 

456DH4

ROLLER KIT, HANGER GAL TYPE w/WIPER – REPLACES 2-D

 

 

 

CAA456B1

Hanger roller – Round profile 1/2″ track – 5/8-11 eccentric stud, 1/8″ shaft shoulder protrusion – vendor entrance application

 

 

CAA456B2

Hanger roller – Round profile 1/2″ track – 5/8-11 eccentric stud, 1/32″ shaft shoulder protrusion – vendor entrance application

 

 

CAA456B3

Hanger roller – Round profile 1/2″ track – 1/2-20 eccentric stud, 1/8″ shaft shoulder protrusion – vendor entrance application

 

 

 

 

207Z4-KIT

ROLLER, UPTHRUST – FOR A & AU HANGERS

 

 

 

456Z1

ROLLER, UPTHRUST w/3/8-24 STUD – TYPE ‘B’ HANGER APPLICATIONS

 

 

456CP1-KIT

ROLLER, (POLY TIRE) UPTHRUST – 1.38″ OD PERMANENT 1/2″ ECCENTRIC PIN

 

 

456CP2-KIT

ROLLER, (STEEL TIRE) UPTHRUST – 1.38″ OD PERMANENT 1/2″ ECCENTRIC PIN

 

 

456DR1

ROLLER, UPTHRUST – 1.38″ OD FOR SHALLOW INTEGRAL HANGER DOOR SYSTEM APPLICATIONS (SEE B6331AS, AY, BC)

 

 

456EK1

ROLLER, UPTHRUST – PERMANENT 1/2″ ECCENTRIC PIN -(IDENTICAL TO 456CP2 EXCEPT POLY TIRE & SLIGHTLY LONGER REACH)

 

 

456FB1

Subs to AAA456ZE2 – (1″ OD) Screw Op. application

 

 

 

AAA456XZ5

Upthrust roller kit w/ hardware – 7/16″ thick shoulder, 1.38″ OD, M12 thread – 1999-2006 application

 

 

 

AAA456XZ6

Upthrust Roller kit, 1/4″ thick shoulder, 1.38″ OD – replaces 2700CAF1 & 456FE1 – Hall OVL and Car HPLIM applications – M12 thread

 

 

AAA456XZ8

ROLLER KIT, 1.38″ OD, .8″ shoulder reach, UPTHRUST ECCENTRIC W/HARDWARE

 

 

 

AAA456YP3

Upthrust roller – used in mod track and hanger applications – M12 stud – (sister hanger roller is AAA456YA3) – used starting 2002

 

 

AAA456YZ1

Upthrust roller – M8 internal threaded hub – OTIS NG door systems (mating screw is ISO7380M8X16-10.9B)

 

 

AAA456ZQ14

Upthrust roller – M12 – Used on glide P applications for MOD track and hanger systems

 

 

 

 

 

65CA2

BOLT, 1/2-20 THREAD (Not eccentric) – FOR A & AU HANGER ROLLERS

 

 

[shown for comparison] 77RK1 early 77RK2 and late 77RK2  – PIN, ECCENTRIC – FOR OLD 456CC, CX APPLICATIONS. (Either no longer needed or typically re-used, special order only)

 

 

 

77RK1

PIN, ECCENTRIC – FOR OLD 456CC APPLICATIONS

 

 

72AF2

NUT, 1/2-20 – FOR VARIOUS HANGER & UPTHRUST ROLLERS USING EITHER PERMANENT OR REMOVABLE 1/2″ STUDS